=============================================================================== MAXTOR 7213S SCSI DRIVE =============================================================================== KEY FEATURES: * 15ms average seek * 64K on-board cache * Low power consumption * Zone density recording * 1:1 interleave * Dual drive master/slave support * Rotary voice coil * Automatic actuator lock * Single-sided surface mount PCBA SPECIFICATIONS: Formatted: ................................. 212,787,200 Million bytes Embedded Controller: ....................... SCSI Actuator type: ............................. Voice Coil Number of Disks: ........................... 2 Data Surfaces: ............................. 4 Data Heads: ................................ 4 Servo: ..................................... Embedded Tracks per surface: ........................ 1,698 Track Density (average): ................... 1,973 tpi Bytes per Block: ........................... 512 Blocks per drive SCSI (User) ............... 415,600 Sectors per track: ......................... 42 physical PERFORMANCE (Typical): Seek times* (ms) Track to track: ....................... 3 Average: .............................. 15 ** Maximum: .............................. 28.2 Average latency (ms) ....................... 8.45 Rotation speed ............................. 3,551 RPM Controller overhead ........................ 1 ms Data transfer rate (Mbytes per sec) To/from media ......................... 2.83 To/from buffer (AT) ................... 9.0 To/from interface ..................... 7.5 Start time / power up (0-3,551 RPM) Typical ............................... <=7 sec Stop time / power down Typical ............................... <=3 sec Start/stop cycles .......................... 20,000 typical Interleave: ................................ 1:1 Buffer Size: ............................... 64K Interface: ................................. AT Recording Method: .......................... 1,7 RLL Recording Density (kbpi) ................... 42.7 maximum Flux Density (kfci) ........................ 32.0 maximum Power Requirments (Typical): Mode +12VDC +-8% +5VDC +-5% Power R/W 145mA 340mA 3.7 W Idle 140mA 330mA 3.5 w Physical: Height: 1.00" (2.54 cm) Length: 5.75" (14.61 cm) Width: 4.00" (10.16 cm) Weight: 1.2 lbs. (.57 kg) Environmental: Temperature (Degrees C) Operating .............................. 5 to 50 Non-operating .......................... -40 to 65 Thermal gradient ....................... 20 per hour max Humidity *** Operating .............................. 5% to 95% non-condensing Non-operating .......................... 5% to 95% non-condensing Maximum wet bulb ....................... 20 degrees C Altitude (relitive to sea level) Operating .............................. -200 to 10,000 feet Non-operating .......................... 40,000 feet max Reliability and Maintenance: MTBF ....................................... >150,000 hours (POH, predicted at 35 degrees C) Preventative Maintenance ................... None Component design life ...................... 5 years (minimum) Data reliability Hard read errors ...................... <10 per 10^13 bits read Shock & Vibration (typical) Shock measured at half-sine pulse. Vibration measured at swept sine, 1 octave per minute Operating shock ........................ 70 Gs, 11ms Non-operating shock .................... 10 Gs, 11ms (without non-recoverable errors) Non-operating Vibration 5-20 Hz ................................ .10" (double amplitude) 20 - 300 Hz ............................ 2 Gs peak amplitude Acoustic Noise 35 dBA at 1 meter (typical) in idle (spinning) on track mode. (sound power -4.5 bels average) * At nominal DC input volages ** The average of 10,000 random seek times (measured on independent test equipment) consitutes the average seek time specification. *** Operating and non-operating specs meet MIL-STD-810E. Method 507.3 Table 507.3-I High humidity diurnal catagory. Natural, High Humidity, Cyclic (Cycle 3) 7213A and 7213S are trademarks of Maxtor Corporation. Specifications subject to change without notice. ============================================================================= 7213S Factory default jumper settings //\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\//\/\/\/\/\/\/\/\/\\ * * * * -#- * * * * +-\ /-/ * /--\ * * *..*J305* /-/ 1 2 3 4 *..*J306+-\ +\ 0 0 0 0 *@@*J307 // * 3 3 3 3 *@@*J308 * // J J J J *..*J309 +\ * /--------------\ +--/ * * * @ @ : : * * * * +--------------/ * * * -#- -#- * * * RP302 RP301 * * * /-----------.\ /-----------.\ * * +------------/ +------------/ * * * +-#---#---#---#-+-+++++++++++++++++++++++++++++++++++++++++-# * . J2 * . J1 * +---------------+-------------------------------------------/ Pin 1 Pin 1 =============================================================================== Maxtor 7213S Jumper Designation /--------+--------------------------------------------------------\ * Jumper * FUNCTION * * Block * * +--------#--------------------------------------------------------# * J301 * Terminator Power * +--------#--------------------------------------------------------# * J302 * Power Up Option * +--------#--------------------------------------------------------# * J303 * Disable Parity * +--------#--------------------------------------------------------# * J304 * Reserved * +--------#--------------------------------------------------------# * J305 * Diagnostic Mode (factory use only) * +--------#--------------------------------------------------------# * J306 * reserved * +--------#--------------------------------------------------------# * J307 * Target ID Address (Most Significant Bit - MSB) * +--------#--------------------------------------------------------# * J308 * Target ID Address * +--------#--------------------------------------------------------# * J309 * Target ID Address (Least Significant Bit - LSB) * +--------+--------------------------------------------------------/ (Shown with Factory Default jumper settings) /------+----------+-----------+-----------+-----------\ * SCSI * Priority * J307 * J308 * J309 * * ID * * * * * +------#----------#-----------#-----------#-----------# * 0 * Lowest * O * O * O * +------#----------#-----------#-----------#-----------# * 1 * * O * O * J * +------#----------#-----------#-----------#-----------# * 2 * * O * J * O * +------#----------#-----------#-----------#-----------# * 3 * * O * J * J * +------#----------#-----------#-----------#-----------# * 4 * * J * O * O * +------#----------#-----------#-----------#-----------# * 5 * * J * O * J * +------#----------#-----------#-----------#-----------# * 6 * * J * * J * * O * +------#----------#-----------#-----------#-----------# * 7 * Highest * J * J * J * +------+----------+-----------+-----------+-----------/ O=OPEN J=JUMPERED * Factory Default Settings BASIC SCSI INSTALLATION STEPS - Drive is shipped with an ID of 6 to provide spare jumpers. Choose address jumpers according to specific installation requirments. - The last physical device on the SCSI bus must be terminated. Any other SCSI device connected between the host and the device at the end of the bus must NOT be terminated. - Install a 50-pin ribbon connector. The striped edge of the 50-pin ribbon cable represents pin 1 and must be oriented towards pin 1 at the drive connector and the host connector. - Install the DC power connector. - Secure the drive in a bay with 6-32 x 1/4" screws. - Set the drive type in the AT BIOS setup to "NOT INSTALLED". Note: This intelligent drive will identify itself to the system and SCSI host adaptor. - The drive is now ready for partitioning and high-level formatting with any operating system. For example: Partition the drive using the FDISK program from MS-DOS version 3.3 or higher. High-level format the drive using the FORMAT command from MS-DOS version 3.3 or higher.